Actions

Difference between revisions of "BOLDscreen"

From SpinozaWiki

(Setting correct screen layout, resolution and refresh rate on 3T)
(Setting correct screen layout, resolution and refresh rate on 3T)
Line 26: Line 26:
 
Setting the correct screen layout, resolution and refresh rate on the 3T-stimulus, v1.0
 
Setting the correct screen layout, resolution and refresh rate on the 3T-stimulus, v1.0
 
# In case of problems, first open “NVIDIA control panel” (right-click in the desktop)
 
# In case of problems, first open “NVIDIA control panel” (right-click in the desktop)
 +
 +
[[Image:boldscreen_troubleshooting_01.jpg|thumb|200px|Select NVIDIA control panel]]
 +
 
# Under “Set up multiple displays”, make sure
 
# Under “Set up multiple displays”, make sure
 
#* displays 1, 2 and 3 are ticked
 
#* displays 1, 2 and 3 are ticked
Line 32: Line 35:
 
#* 2 | 3 are set as primary (as indicated by * in the right top corner, right click on 2|3 and
 
#* 2 | 3 are set as primary (as indicated by * in the right top corner, right click on 2|3 and
 
select “Make primary” if not.
 
select “Make primary” if not.
 
+
 
 +
[[Image:boldscreen_troubleshooting_02.jpg|thumb|200px|NVIDIA control panel]]
 +
 
 
# Under “Change resolution”, make sure
 
# Under “Change resolution”, make sure
 
#*. all three displays are set to PC, 1920 x 1080 (you can select one by left-clicking on the
 
#*. all three displays are set to PC, 1920 x 1080 (you can select one by left-clicking on the
Line 42: Line 47:
 
keep these changes?”. Close the window by clicking X in the top-right corner.
 
keep these changes?”. Close the window by clicking X in the top-right corner.
 
   
 
   
 +
[[Image:boldscreen_troubleshooting_03.jpg|thumb|200px|NVIDIA control panel]]
 +
 
# Close NVIDIA control Panel and open “Screen resolution” (right-click in the desktop)
 
# Close NVIDIA control Panel and open “Screen resolution” (right-click in the desktop)
 +
 +
[[Image:boldscreen_troubleshooting_04.jpg|thumb|200px|Select screen resolution control panel]]
 +
 
# Select display 1 and click “Advanced settings”
 
# Select display 1 and click “Advanced settings”
+
 
 +
[[Image:boldscreen_troubleshooting_05.jpg|thumb|200px|Screen resolution control panel]]
 +
 
 
# Next, go to the tab “Monitor”
 
# Next, go to the tab “Monitor”
 +
 +
[[Image:boldscreen_troubleshooting_06.jpg|thumb|200px|Tab monitor control panel]]
 +
 
# Make sure “Screen refresh rate” is set to 120Hz and select OK. Close the window by clicking X in the top-right corner.
 
# Make sure “Screen refresh rate” is set to 120Hz and select OK. Close the window by clicking X in the top-right corner.
 +
 +
[[Image:boldscreen_troubleshooting_07.jpg|thumb|200px|Tab monitor control panel]]
 +
 
# Do the same for the cloned displays 2|3 (go through steps 5 to 7).
 
# Do the same for the cloned displays 2|3 (go through steps 5 to 7).
 
# You are set for a three-monitor setup after step 10. If you require a two-monitor setup (because
 
# You are set for a three-monitor setup after step 10. If you require a two-monitor setup (because

Revision as of 08:51, 31 May 2019

For stimulus presentation, we use 32" BOLD screen from Cambridge Research Systems at 3T, 7T as well as the mock scanner.

Most important specifications:

  • Size: 32 inch
  • Resolution: 1920 x 1080
  • Refresh Rate: 100 or 120 Hz

3T

  • Distance eye to mirror = ~10cm
  • Distance mirror to screen = ~148cm
  • Total distance ~158cm

7T

  • Distance eye to mirror = ~5cm
  • Distance mirror to screen = ~205cm
  • Total distance ~210cm

Troubleshooting

Screen does not show any image

If the screen does not show any image (also not the test screen) when powering up, check the LED at the back (pinhole). Green indicates nominal function, red malfunction. If red, reseating the SD and power-cycling the screen may resolve the issue.

Setting correct screen layout, resolution and refresh rate on 3T

For pdf version of the instructions on Setting the correct screen layout, resolution and refresh rate on the 3T-stimulus computer, see: Editting screen properties of the stimulus computer

Setting the correct screen layout, resolution and refresh rate on the 3T-stimulus, v1.0

  1. In case of problems, first open “NVIDIA control panel” (right-click in the desktop)
Select NVIDIA control panel
  1. Under “Set up multiple displays”, make sure
    • displays 1, 2 and 3 are ticked
    • 1 is on the left (drag it to the left if not)
    • 2 and 3 are cloned (right click on 3 and select “Clone with 2” if not)
    • 2 | 3 are set as primary (as indicated by * in the right top corner, right click on 2|3 and

select “Make primary” if not.

NVIDIA control panel
  1. Under “Change resolution”, make sure
    • . all three displays are set to PC, 1920 x 1080 (you can select one by left-clicking on the

display)

    • all three displays are set to a refresh rate of 120Hz. If one display is set to another refresh

rate, move on to step 4 after step 3c to change it to the correct rate. Otherwise, you are set for a three-monitor setup after step 3c.

    • If you made any changes, select “Apply” and answer “Yes” when asked “Would you like to

keep these changes?”. Close the window by clicking X in the top-right corner.

NVIDIA control panel
  1. Close NVIDIA control Panel and open “Screen resolution” (right-click in the desktop)
Select screen resolution control panel
  1. Select display 1 and click “Advanced settings”
Screen resolution control panel
  1. Next, go to the tab “Monitor”
Tab monitor control panel
  1. Make sure “Screen refresh rate” is set to 120Hz and select OK. Close the window by clicking X in the top-right corner.
Tab monitor control panel
  1. Do the same for the cloned displays 2|3 (go through steps 5 to 7).
  2. You are set for a three-monitor setup after step 10. If you require a two-monitor setup (because

your task is not programmed to set up the displays correctly), untick display 1 in step 2. After completing your experiment, please enable display one and go through the steps above.

  1. Close all windows by clicking X in the top-right corner.